See What Door Lock Replacement Tricks The Celebs Are Utilizing
Door Lock Replacement - What You Need to Know
If the locks on your door start to show signs of wear and tear, it's usually a good idea to replace them. These signs include things like experiencing difficulty turning the lock, or a key that does not fit.
It is simple to set up new door hardware. It is all you need to do is follow these simple steps.
Deadbolt
The deadbolt is the primary protection of your door against forced entry. It is more durable and secure than the latch that opens the lock. Therefore, you'll want to ensure that the deadbolt you choose cost to replace upvc door lock mechanism purchase is compatible with your needs. If you can, choose deadbolts that are made of case hardened steel and no screw heads exposed on the outside to stop unauthorized drilling. The inside of the deadbolt must be secured to your door frame to enhance security.
During installation, make sure that the bolt on your new deadbolt is extending smoothly through the strike plate while you shut and lock the doors. If it doesn't then use a chisel made of wood to mortise the bolt hole in the strike plate and re-install the deadbolt. Make sure that the doorknob's latch aligns with the hole in the deadbolt when you lock and close the door, too.
Check whether the new deadbolt is compatible with the old one before installing it. The majority of door locks have an illustration of how high the bolt should be placed above the doorknob. However, it's always best to consult a hardware expert for advice if you're not sure what backset measurement you need for your doors. They can direct you to models that are compatible with your door and deadbolt opening.
After ensuring your new bolt assembly is of the proper length, screw it into the hole in the door. If your new deadbolt has a faceplate for the latch, screw it in place, too. It's also a good idea to attach the latch faceplate using the recommended screws to the frame.
Certain lock sets come with a "dummy" or decorative bolt, which allows you to install the keyed deadbolt and still have a functional latch. If you're given the option to use a dummy bolt, it should be installed using the same screws used to install the latch faceplate. This will ensure maximum security.
Some deadbolts have a single cylinder that's only accessible from inside with an open thumb, while other come with a double cylinder that allows keyed and unkeyed entry. It is recommended to select a lock that is commercial grade for maximum security. They've been tested to withstand up to 250,000 cycles of opening and closing before they are sold to homeowners.
Latch
The latch is the part of the lock that retracts the bolt to open and close the door. It is usually fastened by screws on the side, but can be affixed to the strike plate of the door jamb. When replacing upvc door locks a door latch it is important to ensure you choose the right one to match your existing hardware. You can either hold the latch against your existing hardware or look up the label on a new. Dunn Lumber carries a variety of brands, however it is generally recommended to stick with the same brand of your existing hardware to ensure that you receive an appropriate latch that fits correctly.
Certain doors come with a havep instead of a latch. A hasp consists of straps with slots punched in it, which fits over the staple. The staple is then attached to the frame of the door or door with a nail. When the door is shut the strap pulls down on the staple and locks in the position. Commercial buildings employ a hasp since it is cheaper than the lock.
Like any mechanism that has moving parts, a lock can wear out due to repeated use over time. Sometimes, the internal mechanism could "stick" or be difficult to turn. This may require replacement upvc door locking mechanism of the entire lockset. Sometimes, the exterior doorknob can be damaged and it is important to replace that as well.
If your lock is stuck, you can apply some graphite to the keyhole. You can either spray it on the key or sprinkle it onto the interior side of the lock. Then operate the lock a few times to work the graphite into the mechanism. You can also use a screwdriver to remove the knob and reveal the inside components and allow you to see what's going on inside.
Once you've removed all the knobs, find the cylinder with two or three setscrews along the edge of the cylinder. Then tighten them by turning clockwise. The faceplate must be removed and replaced. Surface-mounted rimlocks have an additional set of cylinder setscrews on the back case which must be removed along with the faceplate.
Strike Plate
The strike plate, fixed to the door frame, above the holes that house the master key bolt or deadbolt bolt system, strengthens and improves the security of a locking mechanism. It assists in keeping intruders away by making sure that the latch of the lock is caught by the strike plate when the latch or bolt is engaged. Apart from enhancing security, a top-quality strike plate can also improve the life of a lock.
Standard strike plates are flat pieces of metal with holes, or several holes cut into them. It is attached to the door frame usually with screws, to give the latch something to sink into as it closes. The strike plate must be precisely aligned with the lockset in order to give maximum protection against burglaries.
If the strike plate on the door is damaged, you should replace it as soon as possible. This will ensure that the door will latch and close properly. When replacing a strikeplate, you must first make sure that it is properly aligned with the bolthole in the doorjamb. This can be done by placing a piece of adhesive tape over the bolt hole, and then attempting to test the latch. If the latch does not catch it, take the tape off. Then chisel the area to ensure that the strike plate is aligned with the doorjamb.
After the area has been chiseled it is crucial to use a larger bolt to anchor the strike plate. They should be at least 3 inches long to ensure they are securely fixed to the stud behind the trim board. If you don't install the longer screws, the wood in the doorjamb could split during a robbery attack by a burglar, and leave the door vulnerable.
A professional locksmith will swiftly replace a damaged or worn-out strike plate. They can also install new strike plates on doors that have never been fitted with them before. Additionally, they can upgrade existing strike plates to increase a building's security and improve appearance. This can assist property owners in attracting tenants who want a safer living environment and more peace of mind.
Keys
The key cylinder is a part of your lock that accepts a specific key to shift pins into place so that the inner handle can be turned. The key cylinder is the most important part of your door lock because it fulfills the purpose that locks were made to perform - safeguarding your family, you and your belongings. It is for this reason that people often get their locks rekeyed instead of replacing them.
It is more difficult to replace the lock than simply swap out the existing handle and deadbolt. The old hardware, cylinder and handle (if you have a knob and lock combination) must be removed from the door before a new lock can be installed. There are many DIY-friendly kits that can be used to replace the door lock. However, it's recommended to call a locksmith to ensure the job is done correctly.
It is important that you have the right key before you install your new lock and cylinder. A duplicate key will not perform as expected and could cause the lock to fail and make it impossible for you to open. A trained professional can help you avoid this by ensuring that you have a real, working key for your home.
The next step is to take off the faceplate and then the latch plate. To remove the screws that hold them in place, you will need an screwdriver. If the new plates will be identical to the original ones, you may wish to secure them to save time. If you need to replace them, make sure not to tighten the screws too much because doing so can affect their grip on the door.
After removing the plates, you'll need to measure to determine the proper size of the lock. While many contemporary locksets will fit on a standard thickness of door, it's important to know the dimensions of your door prior to installation to avoid any confusion when you visit the hardware store. Be aware that doorknob locksets can be different sizes from deadbolt locksets, and commercial models can come with an additional bolt or latch.
